Skip to content
Guide

When Does an Industrial Machine Project Need a P.Eng. in BC?

By VitroVentures Engineering · Updated · 8 min read

Many machine and automation projects never need sealed drawings. Some do, and finding out late is expensive. This guide explains, in plain terms, how professional engineering is regulated in British Columbia and the situations where a P.Eng. is commonly involved in machinery projects. It is general information, not legal advice.

Important: this is not legal advice

Whether a specific project legally requires a Professional Engineer depends on the work, the applicable codes and standards, and the requirements of the authority, client or insurer involved. Always confirm requirements with the authority having jurisdiction, your client or insurer, and Engineers and Geoscientists BC (EGBC) when in doubt.

Who regulates engineering in BC

In British Columbia, professional engineering is regulated by Engineers and Geoscientists BC under the Professional Governance Act. Titles such as "Professional Engineer" and "P.Eng." are reserved for registrants. Someone who is not registered may describe their degree, but may not use titles that imply the right to practise engineering.

Firms need a Permit to Practice

Under the Professional Governance Act, firms that practise professional engineering in BC must hold a Permit to Practice from EGBC. EGBC states this applies whether the engineering is done for clients or for the firm’s own internal use, and also to sole practitioners. Firms based outside BC that provide engineering services in BC also need one.

For buyers, this means it is reasonable to ask an engineering firm for its Permit to Practice number, and to check it in EGBC’s public directory.

What a seal means

When a Professional Engineer authenticates a document with their seal, signature and date, they take professional responsibility for its engineering content. EGBC’s guidance describes the seal as a mark of reliance, not a warranty or guarantee of accuracy.

EGBC requires registrants to authenticate documents with engineering content that they prepared or directly supervised and that others will rely on. Preliminary documents not intended for reliance, such as those marked for discussion only, generally do not need to be sealed. EGBC guidance also requires the firm’s Permit to Practice number to appear on authenticated documents.

A registrant may only seal work they prepared or directly supervised. Sealing someone else’s finished design is not a simple stamp: the engineer must be satisfied with the work and take responsibility for it, which usually means a real review and sometimes changes.

Situations where a P.Eng. is commonly involved

The following are situations in machinery and plant projects where engineering by a registrant is often required or requested. Requirements vary, so treat this as a checklist of questions to ask, not a rule.

  • Structural elements: platforms, mezzanines, equipment supports and anchorage, lifting frames and lifting devices
  • Pressure equipment and piping, which are regulated in BC by Technical Safety BC
  • Equipment modifications where an authority, inspector or insurer asks for engineering sign-off
  • Customer specifications that require sealed drawings or an engineer of record
  • Building permit submissions that include equipment, structures or anchorage

Situations where a seal is often not needed

Much day-to-day machine design and automation work is done without sealed drawings: internal improvements, shop drawings for parts, PLC program changes and many drawing packages. Even then, good engineering practice applies, and the client or authority may still ask for engineering review. If you are unsure, ask before the work starts.

Machinery safety standards in BC

In BC, WorkSafeBC’s Occupational Health and Safety Regulation sets requirements for machinery and equipment, including safeguarding and lockout. CSA Z432 (safeguarding of machinery) and related standards are widely used for guarding and safety design. Electrical equipment and panels have their own approval requirements. These requirements apply whether or not a P.Eng. is involved, and a qualified engineer can help interpret them for a specific machine.

Key roles you may hear about

A few terms come up often when sealed work is involved. The engineer of record, or professional of record, is the registrant who takes responsibility for a specific piece of engineering work and authenticates the documents. Under EGBC firm regulation, each firm with a Permit to Practice also has a responsible registrant, who oversees the firm’s professional practice, and a responsible officer from the firm’s leadership.

For a buyer, the important point is simple: know who will be responsible for the engineering on your project, and make sure that person is involved in the work, not only at the end.

Three typical scenarios

Scenario 1: a plant adds a new conveyor and a small platform for maintenance access. The conveyor itself may be designed and built without sealed drawings, but the platform, stairs and anchorage are structural elements that commonly need engineering by a registrant.

Scenario 2: a machine builder ships equipment to a customer whose specification requires sealed drawings for the frame and lifting points. The requirement comes from the contract, so it applies regardless of whether a regulation requires it.

Scenario 3: a plant modifies an existing machine to run faster and heavier product. If the change affects structural loads, guarding or safety functions, the plant may want an engineering review before the change, and an inspector or insurer may ask for one.

These examples are for illustration only. The actual requirement always depends on the specific work and who is asking for it.

Questions to ask an engineering firm

  • Does your firm hold an EGBC Permit to Practice, and what is the number?
  • Who will be the engineer responsible for our project?
  • At what stage will the engineer review the design?
  • What calculations and records will be kept?
  • Is sealing included in the quote, and for which documents?

What the engineer needs from you

To take responsibility for a design, an engineer needs accurate information: loads, materials, operating conditions, the codes or standards that apply, and the requirements of the client or authority. If the work modifies existing equipment, they also need information about the existing equipment, and often a site visit. The more complete this information is at the start, the faster the engineering and review can be done.

Plan for P.Eng. involvement early

The most common and expensive mistake is to design and build first and look for a seal at the end. If a project will need sealed documents, the engineer who will take responsibility should be involved from the start: setting design criteria, reviewing calculations and approving drawings before fabrication.

  • Ask your client, authority or insurer early whether sealed documents are required
  • Get the requirement in writing and include it in the scope and quote
  • Allow time in the schedule for engineering review
  • Keep calculations and design records, not just drawings

Two quick answers

Does a PLC program need a seal? A PLC program is usually not a document that is sealed, but safety-related control design can be engineering work that a client or authority expects a qualified engineer to be responsible for. Ask early.

Can an engineer from another province seal drawings for BC? Registration in another jurisdiction does not give the right to practise or use the title in BC. The engineer must be registered with EGBC, and the firm needs a BC Permit to Practice.

How we can help

We provide mechanical, electrical and controls engineering for industrial equipment and can arrange P.Eng. review and sealing when a project requires it. Tell us at the quote stage, so the engineering is planned in from the beginning.

Sources

Got a drawing? Send it.

Fill out the form for a quote, or email your drawings. We usually reply within one business day.

PREFER EMAIL?
  • Drawings, sketches or CAD (PDF, STEP, DWG)
  • What you need: design, controls, or both
  • Quantity, timeline and site location
info@vitroventures.ca
TALK TO AN ENGINEER +1 604 729 8623Mon to Fri, 8:00 AM to 5:00 PM PST
  • Rockwell, Siemens, Omron, SolidWorks, Inventor
  • P.Eng. support where required
  • Usually reply within one business day
  • On-site in Metro Vancouver & Fraser Valley

Delta, BC, Canada

Request a quote

Takes about a minute. Fields marked * are required.

Email or phone is required, so we can get back to you.

Drawings or files (optional)
Your details are used only to reply to this request. You can also email files to info@vitroventures.ca.